PVC Water Supply Single-Union Ball Valve — Socket & Threaded Ends

PVC Water Supply Single-Union Ball Valve — Socket & Threaded Ends
Item NO:

SAM-UK builds this PVC water supply single union ball valve with one union nut and one
fixed end — the union side is the service side, so the end connector comes off without cutting pipe.
It will not lift the whole body out of a line; that is a double union, and we make those
too.
Socket or BSPP threaded ends, PN16 body, TPV seats, EPDM O-rings, ABS wing handle.

OEM marking available.

Dimension Table for PVC Water Supply Single-Union Ball Valves

  • PN16 — 16 bar at 20 °C
  • 1/2″ – 1″ — 20 / 25 / 32 mm
  • Socket or BSPP — G1/2, G3/4, G1
  • TPV seats, EPDM O-rings, ABS handle
Order

    Quick Help: Contact one of our experts and we'll get back to you in 24 hours!

    Order

      Quick Help: Contact one of our experts and we'll get back to you in 24 hours!

      YouTube
      Instagram
      WhatsApp

      Application

      Construction pipeline system

      Agricultural irrigation pipeline system

      Pool pipeline system

      Industrial pipeline system

      Water treatment pipeline system

      Fishery aquaculture pipeline system

      Advantages

      The characteristics of PVC material: stable physical properties, and not suitable for acid and alkali corrosion, relatively heat-resistant. By adding different additives, PVC materials can present different physical and mechanical properties

      Benefits
      Long service life

      Electrical insulation

      Good impact elasticity

      Good chemical resistance

      Easy to operate

      light in weight

      What the Single Union Body Actually Buys You

      A single union valve has one nut and one fixed end. The union side is the service side: undo the nut
      and the end connector comes off the body — no saw, no drained line, no cutting. What it will not
      do is lift the whole valve out of the pipe.
      That is a double union, a different casting — we make it
      too. Pull a body out of a live manifold and you want the double union; change an end,
      align a thread or replace a cracked connector and this is the cheaper way.

      That last point is the one buyers underrate. The end connector is a separate moulded
      part
      , so a socket valve can become a threaded valve by swapping one piece instead of
      scrapping the whole body. Distributors who stock both end types stop tying up capital in two
      complete SKUs.

      Inside the Body: What Each Part Does

      Six parts, four materials, and only one of them sets the temperature limit. Body, ball,
      stem, end connector, flange and union nut are PVC — the whole wetted path is one material.

      Seats are TPV, O-rings are EPDM, the handle is ABS.

      • PVC body, ball, stem, end connector, union nut — one material through the
        wetted path, so no mixed joint arguing with itself over thermal expansion. The union nut also
        carries the sealing O-ring, which is the part buyers blame last and should blame first.
      • TPV seats — elastomeric, pressed onto the ball by line pressure. They seal at
        low pressure where a hard seat weeps, and they recover rather than creep the way PTFE does under
        sustained load.
      • EPDM O-rings — union nut and stem. The right elastomer for potable water, pool
        water and chlorine; the wrong one for mineral oil, which swells it soft.
      • ABS wing handle — a butterfly, not a lever, so a gloved hand gets hold of it
        in the dark. ABS rather than the PP used on budget valves: stiffer, and it does not go chalky in
        the sun. It is also the part someone eventually puts a cheater bar on.

      The union nut’s O-ring is a compression seal, not a gasket. It seals because it
      sits in a groove under squeeze; crank the nut down hard enough and the ring deforms permanently, then
      weeps — not at commissioning, but a season later. Hand-tight plus a snug quarter turn is the whole
      specification.

      The 60 °C ceiling comes from the PVC, not the seals — TPV and EPDM both run far
      hotter in service. That is why the temperature figure sits beside the pressure figure, not in a
      materials list.

      Socket or Threaded: Choose Once, Live With It

      The body takes either end pattern; the difference is how that end meets the pipe.

      Socket (solvent weld). Permanent, cheapest per joint, and the strongest joint in
      the system when done properly — primer, cement, a square-cut dry end, the full cure window. It never
      comes apart: fine on new build, miserable on a retrofit.

      Threaded. Removable, and the right choice wherever the valve has to come off for
      inspection. Two things kill threaded PVC joints: solvent cement, which should never touch a thread,
      and over-tightening. A PVC male thread will crack before it stops turning, and the crack
      shows up weeks later as a weep — long after the installer has left site.

      The thread form is the other trap. BSPP (ISO 228-1, G thread) is parallel, not tapered,
      and it is not interchangeable with NPT.
      NPT seals on the thread flanks; BSPP needs a face
      seal or an O-ring. Mate the two and you get a joint that holds at low pressure and weeps at test
      pressure — the worst possible timing. We mould to G1/2, G3/4 and G1; check it against the pipe before
      the order, not after.

      Sizes and Pressure Rating

      Three sizes, one water-supply body. Socket and threaded versions share the same body — only
      the end connector changes
      , so a mixed order is one valve design and one spare-parts list.

      Dimensions in mm — symbols as marked on the drawing at the top of this page
      SizeIL1L2d1d2D1D2H
      20 (1/2″)17.579.575.621.5415.050.029.059.5
      25 (3/4″)18.389.680.026.8720.060.734.066.2
      32 (1″)22.3101.090.033.6524.468.042.076.6

      Threaded ends are BSPP: G1/2, G3/4 and G1 against the three sizes. Dimension symbols
      are marked on the line drawing at the top of this page.

      Pressure rating: PN16 (16 bar, 232 psi), quoted on water at 20 °C. Service
      temperature runs to 60 °C maximum, and PVC loses allowable pressure as the line
      warms — at 60 °C this body carries roughly half its cold rating, around 8 bar. A
      pressure figure without a temperature attached is not a rating, it is a guess, which is why both
      belong in the same sentence.

      Standards and Certification

      This model is CE marked and moulded under an ISO 9001 system. Those are the two
      documents we can put in your inbox today.

      It does not carry NSF/ANSI 14 or UPC listing. If the job needs potable-water
      listing for the US or Canada, say so before the order — that is a different product with a
      different test file, not a certificate we can print afterwards. Every claim on this page is
      limited to what the listing actually covers
      , and on this valve that limit is CE plus ISO
      9001.

      Where These Valves Fail in the Field

      Four failures account for nearly every return:

      1. The union nut is over-tightened. The O-ring takes a permanent set and weeps
        within a season. Almost nobody reports this at handover, because at handover it is still
        holding.
      2. The valve is used as a wrenching point. Someone holds the body with a pipe
        wrench while tightening the downstream fitting. The moulding takes a point load it was never
        designed for, and cracks at the shoulder.
      3. Solvent reaches the seat. Welded with the ball shut, or welded too wet, and
        vapour gets to the seat before it flashes off. The valve turns stiff for a month, then stops
        sealing. Leave the ball open while the joint cures — that is not for the ball’s
        sake, it is to give the vapour somewhere to go.
      4. Sunlight. Outdoors, the elastomer goes before the PVC does. A valve that lasts
        a decade indoors will weep after two summers in direct sun unless it is shaded or painted.

      Installation Rules That Actually Matter

      • Support the valve. It is not a pipe hanger. Weight on an unsupported body
        loads the union, and the union is the seal.
      • Follow the arrow. Flow direction is moulded into the body, not printed on a label — it
        survives a repaint and a decade outdoors. Ball valves hold either way, but the arrow is what the
        next man on the job trusts.
      • Stem up or horizontal, never upside down. Debris settles in the cavity and
        scores the ball on the first turn.
      • Do not pressure-test against a closed valve as a dead end. Test the line with
        the valve open, or isolate it and test each side separately.
      • Leave room for movement. PVC grows several times more than steel over the
        same swing, and on a long run the union sees that movement first.

      Why Buyers Stay With SAM-UK

      Taizhou Zhuoxin Plastics has been moulding pipe and fittings since 1995 — 300 to
      350 staff, 50,000 tonnes a year, and a mould shop on the same site as the injection
      lines. That is why a non-standard end configuration or a private-label marking is a drawing revision
      rather than a tooling programme. Valve bodies and union nuts come off our own moulds, so the seal
      face and the nut that loads it are matched by design, not by tolerance stacking.

      Fittings, valves and pipe ship on one set of documents, in one container, on a
      30-45 lead time. For a distributor building a mixed order, that usually
      beats a few points on unit price.

      Frequently Asked Questions

      Single union or double union — which one do I need?

      Single union: the body stays on the pipe, only the end connector comes off. Double union: both
      ends have nuts, so the whole valve lifts out. If a failed body has to come out of a live line,
      you need the double union. If you are changing an end type or replacing a cracked connector, the
      single union does it with one nut and no cutting.

      Can I replace the whole valve without cutting pipe?

      No — and be careful with suppliers who say you can. On this valve only the union-end connector
      comes off; the fixed end is welded or threaded into the run. For full body removal, order the
      double union version.

      Can I use it to regulate flow?

      No. Isolation only. Throttling a part-open ball erodes the seat, and PVC is not built to absorb
      that.

      What will PVC and EPDM not handle?

      Water, most acids and alkalis are fine. Solvents, aromatics and chlorinated hydrocarbons —
      acetone, toluene and their relatives — are not. EPDM also swells on mineral oil, which rules out
      a lot of compressor and hydraulic lines. Check the media against a chemical resistance table
      before the order, not after.

      Installation & Testing

      ① Pipe cutting: according to the use requirements, after measuring the appropriate length, the required pipe can be cut by hand or machine. When cutting, keep both ends vertical and flat, and use a file to cut Deburring and sharp edge, but the chamfer should not be too large.

      ② Bonding of pipes and fittings: before bonding, trial assembly must be carried out, installation position must be determined and marked, length of inserted pipe end (socket depth + 10mm) and inner wall of socket of pipe fittings shall be cleaned,Then wipe with cotton yarn stained with acetone. After acetone volatilizes, evenly brush the adhesive on the outside of pipe end and inside of socket. It should not be too thick, but it should not be missed. Insert after painting and rotate. To the ideal combination angle required for installation, make all the pipes inserted into the socket, fix them by themselves after about 2 to 3 minutes, and wipe off the excess adhesive overflowing from the bonding place to keep the pipe clean. Now cut.Do not force to open or rotate the direction, otherwise it will cause leakage. The adhesive component shall not be subjected to external force within 1 hour, and shall not be watered within 24 hours. The test can be conducted only after the curing time is completed.

      ③ The pipeline installation must have a reliable seal to ensure that there is no leakage in the process of use. Fixing devices (pipe clamps) shall be installed every 1.5m to 2.0m.

      ④ Because the plastic pipe has certain plasticity, when the horizontal pipe is installed, the bracket or elevator is set every 0.6m to prevent the plastic pipe from deformation and affect the use.

      ⑤ The water supply pipe shall be far away from the heat source, and the clear distance between the riser and the stove edge shall not be less than 400mm, and the clear distance between the riser and the heating pipe shall not be less than 200mm.

      ⑥ After construction, the pipe can be sealed with soil only after passing the pressure test.

      ⑦ Please refer to the relevant construction specifications of the Ministry of construction for specific installation and use.